Can anyone recommend a good quality thread adapter which I can get preferably from a UK supplier? I need to convert 1/2" x 28tpi to 1/2" x 20tpi, so the adapter will need to be 1/2 x 28 female and 1/2 x 20 male.
Any suggestions?
Need a thread adapter (1/2 x 28 to 1/2 x 20)
Moderator: dromia
Forum rules
All groups are welcome to post unless your user name is in Newly Registered Red, your post will be removed.
No disparaging remarks, if you don't like what you see then don't buy it.
All groups are welcome to post unless your user name is in Newly Registered Red, your post will be removed.
No disparaging remarks, if you don't like what you see then don't buy it.
-
saddler
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
Why UK?
If it must be the UK then find a lathe operator, as they are easy to do
I just got a VERY nice stainless steel thread adaptor from the USA. 1/2"x28 to 5/8"x24
Let me use my 5/8-24 threaded mod. on my AR barrelled CAM rifles
Was about $24 or so. Very cost effective & VERY well made.
May get another one in due course to allow use on other threaded barrels as I have a 9/16"? (same as FN FAL) thread on my 700 Police.
If it must be the UK then find a lathe operator, as they are easy to do
I just got a VERY nice stainless steel thread adaptor from the USA. 1/2"x28 to 5/8"x24
Let me use my 5/8-24 threaded mod. on my AR barrelled CAM rifles
Was about $24 or so. Very cost effective & VERY well made.
May get another one in due course to allow use on other threaded barrels as I have a 9/16"? (same as FN FAL) thread on my 700 Police.
-
Odd Job
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
Ok, I'll consider it. Where did you get your adapter from?
-
safetyfirst
- Posts: 2651
- Joined: Tue Nov 25, 2014 8:41 am
- Contact:
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
U.K. Custom shop made me one when I ordered a wildcat mod from them, nicely made.
-
safetyfirst
- Posts: 2651
- Joined: Tue Nov 25, 2014 8:41 am
- Contact:
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
Ooh, sorry, can't recall but not very much, perhaps 10-15 quid on top of the mod.
Whatever you get, make sure to get flats machined into it so you can get it off something easily, mine got stuck inside an over barrel mod and I sent it back to get it removed and some flats machined in, takes them a few extra minutes but it's worth it.
Whatever you get, make sure to get flats machined into it so you can get it off something easily, mine got stuck inside an over barrel mod and I sent it back to get it removed and some flats machined in, takes them a few extra minutes but it's worth it.
-
snayperskaya
- Posts: 7234
- Joined: Fri Oct 04, 2013 6:43 pm
- Home club or Range: West Bank of the Volga.....
- Location: West of The Urals
- Contact:
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
What about giving Ovenpaa a shout?.
"The only real power comes out of a long rifle." - Joseph Stalin
Give a man a gun and he can rob a bank.....give a man a bank and he can rob the world!.
More than a vested interest in 7.62x54r!
Give a man a gun and he can rob a bank.....give a man a bank and he can rob the world!.
More than a vested interest in 7.62x54r!
-
sidawson
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
did you get one sorted, as i have one which i ordered from slovakia to use while i waited for my variation but didn't use it as got variation back in a week.
-
Odd Job
Re: Need a thread adapter (1/2 x 28 to 1/2 x 20)
I got that same one, £16 plus £2 postage, seems like a decent part!
Who is online
Users browsing this forum: No registered users and 1 guest