Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Message

#11 Post by **BamBam** » Sat Feb 11, 2017 7:01 pm

I fitted the longer set in my 15-22 yesterday, slightly longer than the receiver is wide, still, screws are loctite in now.

#12 Post by **Blackstuff** » Mon Feb 13, 2017 10:00 am

Brookers wrote:
They are 15/22 specific

Brookers

I'll get a set ordered

s.stimson · #13 Post by **s.stimson** » Mon Feb 13, 2017 12:45 pm

Blackstuff wrote:
Brookers wrote:
Mgi wrote:After lengthy googling I found this: http://www.gunfellas.co.uk/ar-15-anti-w ... -332-p.asp

Order placed - will report how they fit.

Sent from my boing using "An application"
You won't be disappointed. These are the ones I'm using

Brookers
Are they 15-22 specific width or standard AR?

I fitted a set of these to my Bradders built AR15 and they are perfect.

#14 Post by **Blackstuff** » Mon Feb 13, 2017 2:38 pm

What are you doing to me?? A metal AR has a different width (thinner) lower receiver than a plastic 15-22 (wider), so if they fit a metal receiver AR they're not the correct width/length for a 15-22..... Ah well I suppose it was only £15

Anyone need some anti-walk pins?

Mgi · #15 Post by **Mgi** » Mon Feb 13, 2017 9:16 pm

I got mine and they fit 15-22 perfectly!

Sent from my boing using "An application"

#16 Post by **Blackstuff** » Tue Feb 14, 2017 9:28 am

Unless the Bradley Arms AR's have wider than normal receivers, pins which fit properly in a 15-22 would be too wide and stick out of the side of the receiver? If he uses mil-spec lowers and the pins fit properly in them they would be too short for a 15-22....

I'll stop flapping and just wait and see what they're like when they arrive

#17 Post by **Blackstuff** » Fri Feb 17, 2017 3:23 pm

Well the good news is the pins from Gunfellas arrived, the bad news is they're standard length, not 15-22 length aaarggh

15-22 length pins are 25mm+, the ones supplied with my CMC trigger are 22.37mm and the ones from Gunfellas are 22.64mm. I'd put such a small difference down to manufacturing tolerances.

Bah, the search continues....

#18 Post by **Sim G** » Fri Feb 17, 2017 3:32 pm

I've never had the CMC supplied pins with my trigger "walk" and it's done several thousand since fitting. Is this "belt and braces", Mark, or are you having issues?

#19 Post by **Blackstuff** » Fri Feb 17, 2017 4:15 pm

Just belt and braces mate, the ones that came with it work fine (although I noticed the bolts on the trigger pin were loose when I was swapping them over despite blue loctiting them), just prefer to have the exact right stuff in it when I'm using it for competitions

The UK's Finest Independent Forum for Shooters and Gun Owners. Est 2010.

Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Re: Anti-Walk Pin Kit-For Smith & Wesson M&P 15-22 22LR

Who is online