Comprehensive & good quality reloading setup for sale

[Maggot]

Firstly, please note. The prices shown are a guide to how the overall valuation was arrived at and not an invitation for offers. It's a job lot. Chances are the buyer could shift on what they might find they dont need and significantly cut the bill.

Right, I am off, and I ain't coming back. I have been reloading for quite a while and previously loaded FTR loads safely capable of a consistent 6FPS ES around 3200 FPS. These grouped sub .5MOA as would have been required for FTR back then.

I have a full reloading setup to go. It will be all of the above plus what I have since added for .223.

However there is a problem. I don't want to break it down because firstly the kit you may not need now might come in handy later, or you might be able to sell it on. But I don't want to be left with useless items of kit.

I have also left some items FOC because they are specialist, but may be able to be sold on.

Based on this alone, rough cost price is circa £2400.

I am after **£1100** for the following. The prices shown are current prices for new kit.

As hand presses go, the Forster is about the best precision press on the market as regards loading concentric ammunition.

I am putting this on here before I put it anywhere else, and I have time to wait so please don't ask for specific items or to split it down, its a working set up.

**Forster**

Coax press with cover. Described as the Rolls Royce of Dies. Does not need inserts for different cases and dies float so it is virtually impossible to load out of centre ammunition. All dies are fitted with suitable collars that simply slide in and out. **£500**

Original trimmer with Collet for .223/308/303. LR and SR primer pocket cleaners and cone. **£170**

Outside neck trimming kit with pilot for .308 (needs original trimmer to function so goes with kit) **£70**

3in1 neck trimmer .223 **£93**

3in1 neck trimmer .308 (Will do .303. Trims, and chamfers inside and outside as well, carbide blades, needs original trimmer to function) **£93**

.308 Forster bush neck sizer and selection of bushes **£120**

.308 Forster FL sizing die **£60**

.308 Forster Neck sizing die **£60**

.308 Forster NM micrometer seating die **£100**

.30 Forster bullet pulling die (Modified) **£30**

Case neck Mica applicator (dry lube for re-sizing) **£20**

**Hornady**

Lock N Load straight OAL gauge with .308 threaded case **£50**

Lock N Load comparator with basic insert set (Reqs Vernier) **£40**

**Dillon**

Super Swage 600 Complete **£124**

.223 Headspace/case gauge **£36**

**Shooting Shed** (probably THE best, most accurate gauges available)

.308 2p Bump Gauge (Reqs Vernier) **£40**

.308 OAL Gauge (will also indicate over pressure when using Palma brass as the case head will be a tight fit) (Reqs Vernier) **£40**

.223 OAL Gauge (Reqs Vernier) ** £40**

.223 Annealing cup (Fits to electric screwdriver or drill) **£20**

.303 Annealing cup (Fits to electric screwdriver or drill) **£20**

Forster .308 NM mic seater die converted to Shooting Shed bullet pointing die. Made for Optimus HBC, may point other bullets. With anvil for Forster Coax press **£100**

**Redding**

.243 Seater die **£20**

Micro controlled powder thrower and stand **£120**

.223 seater die **£20**

.223 FL resize die **£20**

**Lee**

Hand press with .308 seater die (unused, purchased to adjust OAL on range for tests) **£40**

.223 Collet neck sizer

.223 Crimp die

.223 Seater die

.308 Collet neck sizer

.308 Crimp die

Universal de-capping die **£60 all Lee dies combined**

Hand held Auto prime (and case adaptors for .308/303/223) **£20**

Hand held Ergo prime (and case adaptors for .308/303/223) **£40**

Powder funnel .22-.45

.223 neck trimmer and chamfer (use with cordless driver)

**Sinclair** .308 neck expander die with E + T mandrels

.308 Body only die (made by Shooting Shed)

Various loading trays

Thumlers Tumbler wet cleaner with STM and Seaclean **£350**

Approx 1 gallon IPA with Lanolin and Hand spray (FL Sizing lube) 10% Lanolin by volume

**Lyman**

Primer Sorter

Various flash hole reamers and primer pocket reamers **£30**

GemPro 250 electronic scales (down to 1/200gr) **£140**

**RCBS**

RCBS 10/10 balance scales complete **£120**

RCBS powder trickler **£20**

RCBS Case master gauging tool (used to measure run out and case dimensions to ensure RL process is consistent). Unused, comes with DTI gaugue **£135**

RCBS Precision micrometer .308 (does not require micrometer, use as a before and after firing device to determine die settings) **£65**

Sizing wax (part used)

All manuals as far as I can tell

[Matt101]

/

[Maggot]

SOLD.