Pimping a S&W M&P 15-22

All things rimfire including target, benchrest, hunters, semi autos and plinkers.

Moderator: dromia

Message
Author
breacher

Re: Pimping a S&W M&P 15-22

#11 Post by breacher »

I chopped several .22s to 12" and have never had a problem - just as accurate.
ArcofZen

Re: Pimping a S&W M&P 15-22

#12 Post by ArcofZen »

No, what's the advantage of shortening the barrel?

Fitted the Troy ambidextrous bolt release earlier. Needs a fair bend to get it to fit... Works like a charm though :good:

Image
pbrazendale

Re: Pimping a S&W M&P 15-22

#13 Post by pbrazendale »

Looks really nice, just out of interest which model is this is it the performance centre? And also what brand of moderator did you go for? Thanks


Sent from my boing using "An application"
ArcofZen

Re: Pimping a S&W M&P 15-22

#14 Post by ArcofZen »

Thanks :good:

It's an SAK moderator from 'Jackson Rifles'. Works very well despite being inexpensive. It's not a performance centre, just a standard 15-22. Well, was...
breacher

Re: Pimping a S&W M&P 15-22

#15 Post by breacher »

ArcofZen wrote:No, what's the advantage of shortening the barrel?
More pointable, better balance.

Also much easier to use from a truck cab if you are into rabbiting etc
User avatar
BamBam
Posts: 2695
Joined: Thu Dec 19, 2013 5:23 pm
Location: Royston vasey
Contact:

Re: Pimping a S&W M&P 15-22

#16 Post by BamBam »

ArcofZen wrote:No, what's the advantage of shortening the barrel?
For mini-rifle short and pointable, my rifle with mod, A-Tec Wave, is only as long as a standard rifle.
Image
User avatar
safetyfirst
Posts: 2651
Joined: Tue Nov 25, 2014 8:41 am
Contact:

Re: Pimping a S&W M&P 15-22

#17 Post by safetyfirst »

Also you can put an over barrel mod on a 12" and slip it under a handguard for extra good looks. :)
ArcofZen

Re: Pimping a S&W M&P 15-22

#18 Post by ArcofZen »

Ok, so I need to think more like an 'Operator', got it :D
Ginger
Posts: 356
Joined: Sat Feb 12, 2011 11:50 pm
Contact:

Re: Pimping a S&W M&P 15-22

#19 Post by Ginger »

ArcofZen wrote:No, what's the advantage of shortening the barrel?

Fitted the Troy ambidextrous bolt release earlier. Needs a fair bend to get it to fit... Works like a charm though :good:

Image

Very nice but, loaded Mag, safety off and propped against a log .........
ArcofZen

Re: Pimping a S&W M&P 15-22

#20 Post by ArcofZen »

I knew someone would mention that....

It's physically impossible for the rifle to fire unless the bolt is charged, the trigger is dead and the hammer is forward, if anything it's actually safer than having the bolt charged and the safety on as mechanical safeties can fail like any other movable device, and it's a lot harder to accidentally pull the charging handle all the way back than to flick the safety 90 degrees.

Its also not possible to engage the safety when in this position. Add to the fact that it was on my (large) property and pointing down range with only a hill in the way I'd say it was ok.
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest