First project was to build some bump gauges to fit the Hornady Lock-N-Load Bullet Comparator Body, and here they are, I built one of these at the end of last year to measure shoulder bump and had promised a couple more to people, I ended up with five! They work with .308 parent cases, SAUM. WSM etc.
Shoulder Bump gauges
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Shoulder Bump gauges
My new lathe motor turned up yesterday morning so I spent the afternoon fitting it and hooking it up to the 24v DC power supply I picked up just before Christmas.
First project was to build some bump gauges to fit the Hornady Lock-N-Load Bullet Comparator Body, and here they are, I built one of these at the end of last year to measure shoulder bump and had promised a couple more to people, I ended up with five! They work with .308 parent cases, SAUM. WSM etc.
First project was to build some bump gauges to fit the Hornady Lock-N-Load Bullet Comparator Body, and here they are, I built one of these at the end of last year to measure shoulder bump and had promised a couple more to people, I ended up with five! They work with .308 parent cases, SAUM. WSM etc.
Re: Shoulder Bump gauges
Not a problem, what is the cartridge?
-
spud
Re: Shoulder Bump gauges
284 shehane 6.5 284 and 308 please also dave what are the chances of making me a 284 shehane wilson case holder for the trimmner please
Re: Shoulder Bump gauges
The Bump gauges are not a problem. Not sure about the Wilson Shehane case holder, I have a drawing for the Shehane chamber reamer but no guaging for it. Best bet would be to get an undersized Wilson case holder and ask whoever is chambering your barrel to see if he can run the chamber reamer through the holder, the problem is going to be just how hard the holder you use is....spud wrote:284 shehane 6.5 284 and 308 please also dave what are the chances of making me a 284 shehane wilson case holder for the trimmner please
-
spud
Re: Shoulder Bump gauges
that was muy original plan dave i was trying tosave the finishing remaer
how much are you charging for the pthers please?
how much are you charging for the pthers please?
Re: Shoulder Bump gauges
I can build you a universal bump gauge to suit 6mm to .308. Do you have a couple of Comparator Bodies and are they the red ones or green ones? (Hornady or SincInt) If you have two I can build you the insert to hold the base of the cartridge as well, I would build for a .284 which will also work with the .308 and will mean you can measure the length to a shoulder juncture before pushing the primer out.
They would come with an alignment dowel so you are confident the top and bottom comparator bodies are perfectly aligned.
Cost... Try them and see what you think first as I am looking for feedback at the moment, they are going to be cheap whatever
They would come with an alignment dowel so you are confident the top and bottom comparator bodies are perfectly aligned.
Cost... Try them and see what you think first as I am looking for feedback at the moment, they are going to be cheap whatever
-
spud
Re: Shoulder Bump gauges
red ones dave the head holder would be really handy as well i'll do a reveiw on yt if you dont mind
Re: Shoulder Bump gauges
Sounds like a deal! Are you at BR end of the month? If not PM me your address and I can bung them in the post.
Who is online
Users browsing this forum: No registered users and 2 guests