cast bullets for a Lee Enfield no4
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
dromia
- Site Admin
- Posts: 20125
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: cast bullets for a Lee Enfield no4
Looks like dodgyrog's offering.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: cast bullets for a Lee Enfield no4
I've used the Lee 160gn bullet sucessfully in my 303.
Mould number is CTL312-160-2R and I use it pretty much unfettled apart from smoothing off the sprue plate.
I run them through a 312 sizer, more to get the gas-check fixed than any sizing and coat them with Alox. My lead is range scrap with about 16BH and the finished bullets measure at about .311".
Using the 200 yard load from 'Cast Bullet Loads for Military Rifles' in the Library I get about 1200fps and about a 1inch group at 25m with battle-sights.
Very happy to send you a few if you want to try them out. PM me your address if interested.
Triffid
Mould number is CTL312-160-2R and I use it pretty much unfettled apart from smoothing off the sprue plate.
I run them through a 312 sizer, more to get the gas-check fixed than any sizing and coat them with Alox. My lead is range scrap with about 16BH and the finished bullets measure at about .311".
Using the 200 yard load from 'Cast Bullet Loads for Military Rifles' in the Library I get about 1200fps and about a 1inch group at 25m with battle-sights.
Very happy to send you a few if you want to try them out. PM me your address if interested.
Triffid
-
dodgyrog
- Posts: 4102
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: cast bullets for a Lee Enfield no4
Just to be clear that I am too ill at the moment to be casting!
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
dodgyrog
- Posts: 4102
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: cast bullets for a Lee Enfield no4
Hi Peter, I made them under the Rising Sun Ordnance label.
Theywork well and I'd suggest Alliant 2400 to drive them.
ATB
Roger
Theywork well and I'd suggest Alliant 2400 to drive them.
ATB
Roger
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
Who is online
Users browsing this forum: No registered users and 1 guest